Seeburg LPC1

[Dave N.]

My Seeburg LPC1 was working fine now it will play 33 1/3 but not 45 RP
records.
I replaced the caps in the speed control but did not help. what can b
the cause of this problem Any help would be very helpful

Thanks Dav


--
Dave N.

[c***@yahoo.com]

Dave, does the relay in the speed unit pull in when a 45 mounts?

If so, the problem is either defective power supply in the speed unit or transistors.

if the relay does not pull in, the problem is likely in the contacts on the mech. Check the contacts on the clamp arm which close when a 45 is clamped. There are more contacts on the mech which open the circuit to the relay at all times other than when a 45 is clamped.

The plugs on the LPC series were known for faulty connections as well. Since you removed the speed unit to recap it, it is a good idea to check and clean that plug as well.

The LPC was the most complicated machine of its time. If you have never worked on one a service manual w/schematics is essential.

Have the selection receiver and amp been restored?

You are likely to get more help over at these sites:

http://jukeboxaddicts.proboards.com/

https://www.facebook.com/groups/phonoland

https://groups.yahoo.com/neo/groups/seeburgjukeboxinformationclub/info

RobNYC

[Dave N.]

Post by c***@yahoo.com
Dave, does the relay in the speed unit pull in when a 45 mounts?
If so, the problem is either defective power supply in the speed unit o
transistors.
if the relay does not pull in, the problem is likely in the contacts o
the mech. Check the contacts on the clamp arm which close when a 45 i
clamped.. There are more contacts on the mech which open the circuit t
the relay at all times other than when a 45 is clamped.
The plugs on the LPC series were known for faulty connections as well
Since you removed the speed unit to recap it, it is a good idea to chec
and clean that plug as well.
The LPC was the most complicated machine of its time. If you have neve
worked on one a service manual w/schematics is essential.
Have the selection receiver and amp been restored?
http://jukeboxaddicts.proboards.com/
https://www.facebook.com/groups/phonoland
http://tinyurl.com/yc7gkljx
RobNYC

Thank You for your help. The relay is pulling in when a 45 is clamped
I will check the plugs. when I started this the 45's would start to pla
and slow down almost to a stop so I checked the speed unit and 2 of th
caps had leaks at the ends so I replaced all of them and then a 45 woul
not play at all so your right it may be the plug. The amp and th
controller have be recap and the mute relay replaced. Yes I do hav
service info on the LPC1.
Thanks agin Dav


--
Dave N.

[c***@yahoo.com]

Dave, if the mech runs at 33 and the relay pulls in it is unlikely that the plug is the problem.

-Did you replace the large 4mfd cap? Most people use another oil filled cap, I used 4, 1mfd mylar caps (200 vac or higher)similar to what I've used in the stepper plate circuits. http://photobucket.com/gallery/user/Rob-NYC/media/bWVkaWFJZDoxMjczOTIyMTU=/?ref=1

_Check the speed trimmer pot on the unit front. These are cheap wire-wound and they do develop dead spots. washing or spraying with contact cleaner will usually get them usable again.

-Since the unit did work, albeit poorly, is is possible you made a connection error.

-Check the relay contacts for pitting and make sure there is slight over-travel and "wiping" action.

Transistor can not be overlooked here, but that is rare in this circuit unless there was a short in the motor circuit while a 45 was mounted.

RobNYC

[Dave N.]

Post by c***@yahoo.com
Dave, if the mech runs at 33 and the relay pulls in it is unlikely tha
the plug is the problem.
-Did you replace the large 4mfd cap? Most people use another oil fille
cap, I used 4, 1mfd mylar caps (200 vac or higher)similar to what I'v
used in the stepper plate circuits. http://tinyurl.com/ydyh369e
_Check the speed trimmer pot on the unit front. These are chea
wire-wound and they do develop dead spots. washing or spraying wit
contact cleaner will usually get them usable again.
-Since the unit did work, albeit poorly, is is possible you made
connection error.
-Check the relay contacts for pitting and make sure there is sligh
over-travel and "wiping" action.
Transistor can not be overlooked here, but that is rare in this circui
unless there was a short in the motor circuit while a 45 was mounted.
RobNYC

Yes I replaced it with a 4mfd oil cap. I did not know you could us
mylars to replace a oil. I will check the control and clean it. coul
the relay have a bad contact on it


--
Dave N.